Does the model suit your lighting task?
Steinel XLED home 2 S white (033088), LED floodlight with motion sensor, IP44… stands in this selection for a house wall, driveway or yard with an existing 230 V connection and a motion sensor. It is not intended as a constant light, not for tenants without a qualified electrician and not for use in direct jets of water. That is a narrower and more honest statement than a blanket “good” or “bad”. A lamp can be technically sound and still disappoint in the wrong place. That is why this review begins with the intended use, not with a score.
The deciding figure is the sensor range, with the working shown: according to the manufacturer it is radial r equals 5 metres (39 square metres) and tangential r equals 10 metres (157 square metres), with a 180 degree detection angle and an optimal mounting height of 2 metres. The luminous efficacy is 1,550 lumens divided by 13.7 W, so around 113 lumens per watt, class E. EPREL lists the device as non-directional and mains-operated, so the factor 1.000 applies.
For this model, 6 readable product features from the Amazon listing are available. They are not presented as independently confirmed measured values. We explicitly separate what the source states from our practical assessment. We do not claim any long-term, laboratory or room evaluation of our own. We reproduce the quoted listing texts unchanged in content, but apply the house punctuation: dashes become a colon or comma, ranges of values are written out with “to”, and special characters and promotional symbols are removed. Numbers, units and statements are left untouched.
Product data and sources
| Product | Steinel XLED home 2 S white (033088), LED floodlight with motion sensor, IP44… |
|---|---|
| Brand | Steinel |
| Category | Home lighting |
| ASIN | B01MFF6Y5S |
| Sources as of | 21 October 2026 |
| Type of research | Data and source analysis; no laboratory or long-term trial of our own |
Listing detail: The freely swivelling LED panel of the spot light is…
What the source says: The freely swivelling LED panel of the spot light can be adjusted flexibly by up to 180° and can therefore be aligned in any direction
Why this matters: Adjustability is only useful if the range of movement stays free at the planned location and the lamp holds its position reliably.
Listing detail: At only 13.7 W consumption the outdoor floodlight lights…
What the source says: At only 13.7 W consumption the outdoor floodlight lights the driveway, yard, garden and terrace with a brightness of 1,550 lumens and a warm white colour temperature of 3000 K
Why it matters: The amount of light can only be assessed together with beam angle, distance and the area lit. A high figure alone does not yet say whether the light arrives in the right place.
Listing detail: The 180° infrared motion sensor of the floodlight detects…
What the source says: The 180° infrared motion sensor of the floodlight reliably detects movement up to a maximum range of 10 m, swivelling 180° vertically and 90° horizontally
Why it matters: With a sensor, detection angle, range, mounting height and possible false triggering all count. These points cannot be fully derived from a bare mention of a function. According to the manufacturer the 10 metres apply only tangentially, that is across the viewing direction of the sensor. Radially, directly towards the sensor, Steinel gives 5 metres (39 square metres). Plan the alignment so that people walk across the detection area and not straight towards the floodlight. The angles are swapped in the listing. According to the manufacturer the sensor covers 180 degrees horizontally and 90 degrees vertically. According to the manufacturer the luminaire panel swivels 180 degrees horizontally and 180 degrees vertically.
Listing detail: Simple and quick setting of the overrun time 8 sec…
What the source says: Simple and quick setting of the overrun time 8 sec., 35 minimum and dusk threshold 2-2000 lx on the underside of the sensor
Why it matters: A lux figure must always come with the measuring distance. As this distance grows, markedly less illuminance reaches the eye or the work surface. The data sheet and the manufacturer’s page give 2 to 1,000 lux, not 2,000. According to the manufacturer the overrun time is 5 seconds to 35 minutes, not from 8 seconds. Where there are differences, the manufacturer’s document applies.
Listing detail: Never change a light bulb again thanks to 50,000 h…
What the source says: Never change a light bulb again thanks to 50,000 h LED rated lifetime through a new, highly heat-conductive cooling system (Hcmc), simple mounting and convenient cabling through the intelligent Steinel mounting concept
Why it matters: This point should be checked against dimensions, instructions and the existing installation before buying. A listing can contain variants or shortened wording. According to the manufacturer the light source is not replaceable. That means the whole device has to be replaced if the LED fails. The 50,000 hours are a manufacturer statement about the LED, not about the whole luminaire.
Listing detail: scope of delivery
What the source says: Scope of delivery: LED floodlight, mounting material (2x screws, 2x wall plugs, 3x spacers, 2x sealing plugs), cover plate, operating instructions | Dimensions (L x W x H): 16.1 x 18.0 x 21.8 cm | Weight: 0.576 kg | Article number: 033088
Why it matters: Check how many ways of operating it there really are and whether each of them stays reachable at the planned spot. It also matters whether the device stores the level last selected and whether an accidental touch changes a setting. The manufacturer’s page gives 0.547 kilograms as net weight. The difference of around 29 grams may come from packaging or accessories, but that is not documented.
Use in daily life
The floodlight is not stood up but screwed to the wall or into a corner (surface mounting, corner wall bracket not included). It needs no plug but a fixed connection at 220 to 240 V, and it is operated via potentiometers on the underside of the sensor. According to the manufacturer the panel can be swivelled 180 degrees horizontally and vertically, and the sensor covers 180 degrees horizontally and 90 degrees vertically. There is no battery and no solar operation.
For this model, the purchase decision should therefore hinge on a concrete situation. Before buying, write a sentence such as: “I need light for …” and add place, time of day and activity. If the model does not clearly fulfil this task, an alternative from the same category is probably the better choice.
The floodlight is not a constant light, because according to the manufacturer it has no basic light function. It is not built for use with jets of water (IP44 means splashing water) and not for places at risk of impact (IK03). It does not replace path lighting or an alarm system. The sensor function is a convenience, not burglary protection.
Strengths and limits of the assessment
What speaks for the model
- Product image, ASIN and listing data are clearly linked to one another.
- The design can be matched to a specific lighting task: for a house wall, driveway or yard with an existing 230 V connection and a motion sensor, not as a constant light, not for tenants without a qualified electrician and not for use in direct jets of water.
- The available features allow a targeted check before buying, without inventing a star rating.
What remains open
- No long-term use of our own, no light measurement and no documented load check.
- Listing details can be abbreviated or change with variants and model updates.
- Room effect, glare and ease of use depend on your location and daily routine.
The purchase most often fails on the connection: anyone without an existing lighting point needs a qualified electrician, and the installation then costs more than the lamp. The second mistake is the range, when the sensor points straight at the driveway and detects only about 5 metres. The third mistake is the location: direct rain from above or jets of water overwhelm IP44. In addition, the device has to be replaced if the LED fails.
What you should measure and check before buying
Before buying, check whether a connection already exists at the mounting spot and whether the cable is compatible with the device. Measure the height above the ground, because the manufacturer gives 2 metres as optimal and 4 metres as the maximum. Decide from which direction people will approach, so that they walk across the detection area and not straight towards the sensor. Check whether the spot is under an overhanging roof, because IP44 only covers splashing water.
- Decide whether you need a motion sensor floodlight or a constant light: These are two different device classes. According to the manufacturer this model has no basic light function and switches only on movement and dusk.
- Check the connection: Mains 220 to 240 V, Class II according to the manufacturer, no plug mentioned. Before buying, clarify whether a lighting point exists and who will connect it.
- Check the mounting location: Optimal height 2 metres, maximum 4 metres according to the manufacturer. Choose the wall so that people walk across the detection area.
- Check the IP rating against the location: According to the manufacturer, IP44 stands for splashing water. It is not intended for a direct jet or permanent wetness.
- Check the model identifier: Article number 033088 and EAN 4007841033088 for the white version without networking. Other XLED home 2 models differ in power and function.
If you are unsure how much light your room needs at all, work it out once: the lumens-to-watts chart translates wattage figures into actual brightness, and how many lumens per room are needed depends on area and activity. Further models from this area are in the overview under home lighting, and the lighting calculator translates your room into a concrete target brightness.
Set-up, position and first check
When mounting, the connection matters more than the screws. Check the cable, the mounting height (optimal 2 metres, maximum 4 metres according to the manufacturer) and the viewing direction of the sensor. Set the dusk threshold and the overrun time on the potentiometers; the manufacturer’s range is 2 to 1,000 lux and 5 seconds to 35 minutes. If in doubt at the connection point: qualified electrician.
After set-up, do not judge the light only in daylight. In the evening, switch the rest of the lighting as you normally use it, and check the situation from seated, standing and walking height. Only then do disturbing reflections, hard shadows or an unfavourable switch position become visible.
Keep the instructions and the model designation. This helps with spare parts, with a later query about the product and in a guarantee case. Replacing the light source is not intended; at the end of its rated lifetime the whole device is replaced. For a hard-wired mains connection, damp locations and outdoor mounting, the rule is: if the existing installation does not clearly match the instructions, the work belongs in professional hands.
Comparison with similar models
The comparison does not name winners. It shows models of the same category so that you can see whether one of them is closer to your lighting task. If two models have the same task in the Assessment column, they do not differ in purpose but in design, dimensions and features. The column then states what is actually different according to the sources.
| Model | Brand | Assessment | Details |
|---|---|---|---|
| Steinel XLED home 2 S white (033088), LED floodlight… | Steinel | for a house wall, driveway or yard with an existing 230 V connection and a motion sensor, not as a constant light, not for tenants without a qualified electrician and not for use in direct jets of water | This review |
| Steinel XLED home 2 SC Connect 065447 | Steinel | for a driveway, yard or house wall with a fixed 230 V supply cable, as a motion light with app settings, not as a constant floodlight for large areas and not for tenants without a qualified electrician | Read the analysis |
| Oktaplex Rio outdoor light with motion sensor | Oktaplex lighting | for a front door, garage wall or terrace door on an existing 230 V supply cable, not for tenants without a qualified electrician and not for permanently damp locations or large areas | Read the analysis |
Our buying decision
Steinel XLED home 2 S white (033088), LED floodlight with motion sensor, IP44… makes sense if you want a floodlight for a house wall, driveway or yard with an existing 230 V connection and a motion sensor, have checked the dimensions at the intended spot and will actually use the functions named in the listing. The purchase is less convincing if you expect a universal solution for several conflicting lighting tasks.
Keep looking if key data such as dimensions, light output, IP rating or compatibility is not clearly documented for your intended use. The same applies if you only like the look of the design, but the cable, the installation location or the controls would get in your way in daily use.
We deliberately award no stars. A numerical score would suggest a measurement accuracy that does not exist without documented hands-on testing. The statement this page can support is narrower: which details are available, what the model may be suited for, and which questions remain open before you buy?
Frequently asked questions about the outdoor floodlight
May I connect the XLED home 2 S myself?
That depends on your installation, and if in doubt the rule is: qualified electrician. According to the manufacturer the device has a 220 to 240 V mains connection and Class II, and no document mentions a plug. If only a cable comes out of the wall, this is work on the installation, which Section 13 of the German Low Voltage Connection Ordinance (NAV) reserves for registered installation companies.
Is the floodlight waterproof?
No. According to the manufacturer it has the IP44 rating, where the second digit 4 stands for splashing water. Waterproof in the sense of the standard only starts at a second digit of 7, so the device does not belong anywhere it will be hosed down with a garden hose or pressure washer.
Is a range of 10 metres enough for a long driveway?
Only to a limited extent. According to the manufacturer, 10 metres applies tangentially, that is across the sensor, and only 5 metres radially. If someone walks straight towards the floodlight, it is only detected at around 5 metres according to the manufacturer. For a long driveway, mounting at the side is better than on the end wall.
How bright is the floodlight and what energy class does it have?
According to the manufacturer it delivers 1,550 lumens at 13.7 W, which is around 113 lumens per watt. Under Regulation (EU) 2019/2015 that gives class E, and EPREL lists the device under registration number 1003004. For how an area is actually lit, the data sheet gives a light distribution curve; we have not evaluated the figures from it.
Can I replace the light bulb if it fails?
No. According to the manufacturer, the light source and control gear are not replaceable. If the LED fails, the luminaire has to be replaced. The manufacturer’s page states a guarantee of 5 years; we have not checked the conditions.
Can the floodlight be run as a constant light?
According to the manufacturer’s page, this model has no basic light function. It switches via the motion sensor and the dusk setting. According to the manufacturer the overrun time can be set from 5 seconds to 35 minutes, and a true constant light is not described.
Sources and currency
The sources are ranked by their closeness to the product: manufacturer documents come before retailer or comparison data. A shop listing is useful for the variant currently on offer, but it is not an independent check. Missing documents are not replaced with invented experiences.
- Manufacturer page of Steinel GmbH for the XLED home 2 S white, article number 033088, EAN 4007841033088, retrieved 21 October 2026: power 13.7 W, luminous flux 1,550 lumens, 113 lumens per watt, energy efficiency class E, 3000 K, CRI 82, IP44, impact resistance IK03, Class II, mains connection 220 to 240 V at 50 to 60 Hz, ambient temperature minus 20 to plus 40 degrees Celsius. Sensor: detection angle 180 degrees, range radial 5 metres (39 square metres) and tangential 10 metres (157 square metres), sensor 180 degrees horizontal and 90 degrees vertical, mounting height maximum 4 metres, optimal 2 metres, creep-under protection and segment-wise masking available. Dusk setting 2 to 1,000 lux, overrun time 5 seconds to 35 minutes, set via potentiometers, no basic light function, no networking. Light source not replaceable, manufacturer guarantee 5 years according to the manufacturer’s page. Dimensions 161 by 180 by 218 millimetres, weight 0.547 kilograms. The page lists downloads for operating instructions and wiring diagrams; the files themselves were not opened for this dossier.
- Data sheet of Steinel GmbH for the XLED home 2 S (PDF, as of October 2026, retrieved 21 October 2026): confirms IP44, IK03, Class II, 13.7 W, 1,550 lumens at 3000 K, overall product efficacy 113 lumens per watt, detection angle 180 degrees, range radial 5 metres and tangential 10 metres, dusk setting 2 to 1,000 lux, time setting 5 seconds to 35 minutes, light source and control gear not replaceable, surface mounting on a wall or corner, corner wall bracket not included. The data sheet contains a detection diagram, a light distribution curve and a wiring diagram as graphics.
- EU product register EPREL, registration 1003004 of Steinel GmbH for model identifier 4007841033088, retrieved 21 October 2026: luminous flux 1,550 lumens, on-mode power consumption 13.7 W, energy efficiency class E, mains-operated (mains MLS), non-directional (directional NDLS), not dimmable, not colour-tuneable, not networked, CRI 82, standby power 0.5 W, placed on the market from 31 August 2021, survival factor 0.9, lumen maintenance factor 0.98.
- Listing page for ASIN B01MFF6Y5S on Amazon.co.uk, retrieved 21 October 2026 via the editorial product data: the listing text gives 13.7 W, 1,550 lumens, 3000 K, motion sensor 180 degrees with 10 metres range, panel swivels 180 degrees, overrun time 8 seconds to 35 minutes, dusk threshold 2 to 2,000 lux, 50,000 hours rated lifetime, weight 0.576 kilograms, article number 033088. This is a seller statement and not a manufacturer document. Amazon listing B01MFF6Y5S, not linked
- licht.de, portal of the Fördergemeinschaft Gutes Licht, on the ingress protection ratings of luminaires, retrieved 21 October 2026: The IP code consists of two digits, the first describing protection against foreign objects and contact, the second protection against water ingress. IP 44 stands for protection against splashing water.
- Overview of ingress protection ratings under BS EN 60529 with the table for the second digit, retrieved 21 October 2026: 3 spraying water, 4 splashing water, 5 water jets, 6 powerful water jets, 7 temporary immersion. Waterproof applies only from a second digit of 7.
- licht.de on the energy efficiency classes for light sources in force since 1 September 2021, retrieved 21 October 2026: Class E applies from 110 to 134 lumens per watt, class D from 135, class F from 85 to 109.
- Section 13 of the German Low Voltage Connection Ordinance (NAV), retrieved 21 October 2026: Electrical installations behind the house connection fuse may, apart from the network operator, only be installed, extended, modified and maintained by an installation company entered in an installer register.
- Amazon product listing B01MFF6Y5S; product data via the Creators API, retrieved 21 October 2026 Advertisement
Content checked on 21 October 2026. Prices, availability and product variants can change independently of this page. For the final check, always use the current retailer listing and any available manufacturer documents.
If a linked source is no longer reachable, or the model on offer visibly differs from the product image and designation, this analysis is no longer the right basis for a decision. In that case the current model number is what counts. Tell us about the difference via the contact page (in German), so that the data, the link and the recommendation can be checked.
